User Tools

Site Tools


network_space_v2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
network_space_v2 [2012/09/08 14:07]
82.234.233.9
network_space_v2 [2012/09/08 14:14]
82.234.233.9 minor change
Line 28: Line 28:
  
 The boards are almost fully supported mainline. For more informations,​ see our [[ubootforkirkwoodsocs|U-Boot for Kirkwood]] page. The boards are almost fully supported mainline. For more informations,​ see our [[ubootforkirkwoodsocs|U-Boot for Kirkwood]] page.
- 
-These are the default environment variables in the stock U-Boot provided by Lacie: 
-<​code>​ 
-baudrate=115200 
-loads_echo=0 
-rootpath=/​mnt/​ARM_FS/​ 
-netmask=255.255.255.0 
-console=console=ttyS0,​115200 mtdparts=spi_flash:​0x80000@0(uboot)ro,​0x300000@0x100000(root) 
-CASset=min 
-MALLOC_len=1 
-ethprime=egiga0 
-bootargs_root=root=/​dev/​nfs rw 
-bootargs_end=:::​DB88FXX81:​eth0:​none 
-image_name=uImage 
-standalone=fsload 0x2000000 $(image_name);​setenv bootargs $(console) root=/​dev/​mtdblock0 rw ip=$(ipaddr):​$(serverip)$(bootargs_end) $(mvPhoneConfig);​ bootm 0x2000000; 
-ethmtu=1500 
-mvPhoneConfig=mv_phone_config=dev0:​fxs,​dev1:​fxs 
-mvNetConfig=mv_net_config=(00:​11:​88:​0f:​62:​81,​0:​1:​2:​3),​mtu=1500 
-usb0Mode=host 
-yuk_ethaddr=00:​00:​00:​EE:​51:​81 
-netretry=no 
-rcvrip=169.254.100.100 
-loadaddr=0x02000000 
-autoload=no 
-ethact=egiga0 
-stderr=serial 
-mainlineLinux=no 
-enaMonExt=no 
-enaCpuStream=no 
-enaWrAllo=no 
-pexMode=RC 
-disL2Cache=no 
-setL2CacheWT=yes 
-disL2Prefetch=yes 
-enaICPref=yes 
-enaDCPref=yes 
-sata_dma_mode=yes 
-netbsd_en=no 
-vxworks_en=no 
-disaMvPnp=no 
-enaAutoRecovery=yes 
-start_lump=lump 3 
-resetdisk=ide reset 
-bootdelay=0 
-boot_fail=lump 
-kernel_addr=0x800000 
-productType_env=ASTON_KW 
-primaryPart=6 
-secondaryPart=A 
-resetFlag_env=0 
-bootargs=console=ttyS0,​115200 root=/​dev/​sda7 ro reset=0 productType=ASTON_KW 
-bootcmd=run disk_disk 
-boot_disk4=disk ${kernel_addr} 1:​${primaryPart};​ setenv rootfs /dev/sdb7; 
-boot_disk3=if disk ${kernel_addr} 0:​${primaryPart};​ then setenv rootfs /dev/sda7; else run boot_disk4; fi 
-boot_disk2=if disk ${kernel_addr} 1:​${secondaryPart};​ then setenv rootfs /dev/sdb7; else run boot_disk3; fi 
-boot_disk1=if disk ${kernel_addr} 0:​${secondaryPart};​ then setenv rootfs /dev/sda7; else run boot_disk2; fi 
-boot_disk=if test ${resetFlag_env} -eq 0; then run boot_disk1; else run boot_disk3; fi 
-disk_disk=run boot_disk; setenv bootargs console=ttyS0,​115200 root=${rootfs} ro reset=${resetFlag_env} productType=${productType_env};​ bootm ${kernel_addr};​ 
-ethaddr= #mac address 
-ipaddr= #NAS ip 
-ncip= #clunc connected ip 
-serverip= #clunc connected ip 
-stdin=nc 
-stdout=nc 
-</​code>​ 
  
 ===== Linux ===== ===== Linux =====
Line 101: Line 36:
 ===== Userspace ===== ===== Userspace =====
  
-===== LaCie stock system =====+===== LaCie system =====
  
 For more informations about the LaCie stock system, look [[lacie_stock|here]]. For more informations about the LaCie stock system, look [[lacie_stock|here]].
- 
-===== Auto power on ===== 
- 
-Normally, after applying power, you have to push the button to turn on the ns2. If you want it to switch on automatically,​ you have to switch a bit in the i2c eeprom. 
-The bit is at offset 14 in the eeprom, changing it from 0 to 1 will enable auto switch on. 
-For more details see [[ubootforkirkwoodsocs#​eeprom_organization]] 
  
network_space_v2.txt ยท Last modified: 2012/09/08 14:16 by 82.234.233.9