User Tools

Site Tools


network_space_v2

This is an old revision of the document!


LaCie Network Space v2

This page is relevant for Network Space (Max) v2 and Internet Space v2 boards.

Since mid-2011 lacie change the hardware configuration of the network space v2 to a lower one, see LaCie Network Space Lite v2.

Hardware

  • CPU ARM926EJ-S (ARMv5TE) 800MHz
  • SoC Kirkwood 88F6281_A0
  • SDRAM memory 256MB, DDR2 267MHz
  • SPI flash, NOR 512kB (MACRONIX MX25L4005CMI-12G)
  • Ethernet Gigabit port (PHY MARVELL 88E1116R)
  • 1 USB2 port, 1 connector host and 1 connector device (except for Internet Space v2)
  • 1 SATA port (2 ports for Network Space Max v2)
  • I2C EEPROM, 512 bytes (24C04 type)
  • 2 LEDs (blue and red with CPLD SATA activity blink)
  • Power push button

Network Space v2 Network Space v2

Openocd

An unreliable configuration is available here

U-Boot

The boards are almost fully supported mainline. For more informations, see our U-Boot for Kirkwood page.

These are the default environment variables in the stock U-Boot provided by Lacie:

      baudrate=115200
      loads_echo=0
      rootpath=/mnt/ARM_FS/
      netmask=255.255.255.0
      console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x300000@0x100000(root)
      CASset=min
      MALLOC_len=1
      ethprime=egiga0
      bootargs_root=root=/dev/nfs rw
      bootargs_end=:::DB88FXX81:eth0:none
      image_name=uImage
      standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
      ethmtu=1500
      mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
      mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
      usb0Mode=host
      yuk_ethaddr=00:00:00:EE:51:81
      netretry=no
      rcvrip=169.254.100.100
      loadaddr=0x02000000
      autoload=no
      ethact=egiga0
      stderr=serial
      mainlineLinux=no
      enaMonExt=no
      enaCpuStream=no
      enaWrAllo=no
      pexMode=RC
      disL2Cache=no
      setL2CacheWT=yes
      disL2Prefetch=yes
      enaICPref=yes
      enaDCPref=yes
      sata_dma_mode=yes
      netbsd_en=no
      vxworks_en=no
      disaMvPnp=no
      enaAutoRecovery=yes
      start_lump=lump 3
      resetdisk=ide reset
      bootdelay=0
      boot_fail=lump
      kernel_addr=0x800000
      productType_env=ASTON_KW
      primaryPart=6
      secondaryPart=A
      resetFlag_env=0
      bootargs=console=ttyS0,115200 root=/dev/sda7 ro reset=0 productType=ASTON_KW
      bootcmd=run disk_disk
      boot_disk4=disk ${kernel_addr} 1:${primaryPart}; setenv rootfs /dev/sdb7;
      boot_disk3=if disk ${kernel_addr} 0:${primaryPart}; then setenv rootfs /dev/sda7; else run boot_disk4; fi
      boot_disk2=if disk ${kernel_addr} 1:${secondaryPart}; then setenv rootfs /dev/sdb7; else run boot_disk3; fi
      boot_disk1=if disk ${kernel_addr} 0:${secondaryPart}; then setenv rootfs /dev/sda7; else run boot_disk2; fi
      boot_disk=if test ${resetFlag_env} -eq 0; then run boot_disk1; else run boot_disk3; fi
      disk_disk=run boot_disk; setenv bootargs console=ttyS0,115200 root=${rootfs} ro reset=${resetFlag_env} productType=${productType_env}; bootm ${kernel_addr};
      ethaddr= #mac address
      ipaddr= #NAS ip
      ncip= #clunc connected ip
      serverip= #clunc connected ip
      stdin=nc
      stdout=nc
     
      

Linux

The boards are almost fully supported mainline. For more informations, see our Linux for Kirkwood page.

Userspace

Auto power on

Normally, after applying power, you have to push the button to turn on the ns2. If you want it to switch on automatically, you have to switch a bit in the i2c eeprom. The bit is at offset 14 in the eeprom, changing it from 0 to 1 will enable auto switch on. For more details see eeprom_organization

network_space_v2.1330519226.txt.gz · Last modified: 2012/02/29 12:40 by 83.163.254.51